Cisco CCNA 3 Simulation v6.0 Test Chapter 1
-
Questions and answers - 10/10
10/10
CCNA 3 Chapter 1 Quiz Questions and Answers. In this simulation, take your test, get your score and share with others!
- Points: 56
- Questions: 28
- Time limit: None
- Allowed attempts: Unlimited
Check all the CCNA exams in THIS SECTION.
Exam Chapter 1 Questions and Answers CCNA 3 V6.0
Which action should be taken when planning for redundancy on a hierarchical network design?
One method of implementing redundancy is path redundancy, installing alternate physical paths for data to traverse the network. Redundant links in a switched network supports high availability and can be used for load balancing, reducing congestion on the network.
Which statement describes a characteristic of Cisco Catalyst 2960 switches?
Cisco Catalyst 2960 switches support one active switched virtual interface (SVI) with IOS versions prior to 15.x. They are commonly used as access layer switches and they are fixed configuration switches.
Which statement describes a characteristic of Cisco Meraki switches?
The Cisco Meraki cloud-managed access switches enable virtual stacking of switches. They monitor and configure thousands of switch ports over the web, without the intervention of onsite IT staff.
Refer to the exhibit. Which devices exist in the failure domain when switch S3 loses power?
A failure domain is the area of a network that is impacted when a critical device such as switch S3 has a failure or experiences problems.
In which situation would a network administrator install a Cisco Nexus Series or Cisco Catalyst 6500 Series switch to promote infrastructure scalability?
Cisco Nexus Series switches are employed on data centers to promote infrastructure scalability, operational continuity, and transport flexibility. They also provide secure multitenant services by adding virtualization intelligence technology to the data center network.
In the Cisco Enterprise Architecture, which two functional parts of the network are combined to form a collapsed core design? (Choose two.)
Por favor, selecciona 2 respuestas correctas
What are two ways to access a Cisco switch for out-of-band management? (Choose two.)
Por favor, selecciona 2 respuestas correctas
Which two requirements must always be met to use in-band management to configure a network device? (Choose two.)
Por favor, selecciona 2 respuestas correctas
Direct connections to the console and auxiliary ports allow for out-of-band management. Terminal emulation software is not always required because in-band management can be performed using a browser.
Refer to the exhibit. Which command was issued on a Cisco switch that resulted in the exhibited output?
The show port-security address command displays all secure MAC addresses configured on all switch interfaces. The show mac-address-table command displays all MAC addresses that the switch has learned, how those addresses were learned (dynamic/static), the port number, and the VLAN assigned to the port. The show vlan brief command displays the available VLANs and the ports assigned to each VLAN. The show vlan summary command displays the count of all configured VLANs.
What capability is provided by the use of application-specific integrated circuits in Cisco multilayer switches?
Application-specific integrated circuits (ASICs) increase the forwarding speed of a switch by allowing packets to bypass the CPU for processing.
When a Cisco IOS device is being selected or upgraded, which option indicates the capabilities of the Cisco IOS device?
The version number and release number refer to the overall device operating system. The platform refers to the specific model of a device. The feature set determines what a particular device is capable of.
Which type of information is displayed by the show ip protocols command that is issued from a router command prompt?
The show ip protocols command displays information about the routing protocols that are configured, the networks the router is advertising, and the default administrative distance. The show interfaces command displays interfaces with line (protocol) status, bandwidth, delay, reliability, encapsulation, duplex, and I/O statistics. The show ip interfaces command displays interface information, including protocol status, the IP address, whether a helper address is configured, and whether an ACL is enabled on the interface. The show protocols command displays information about the routed protocol that is enabled and the protocol status of interfaces.
A network technician needs to connect a PC to a Cisco network device for initial configuration. What is required to perform this device configuration?
Because the device needs to be initially configured, a network connection is unavailable yet on this device, hence the need for an out-of-band management method. A configuration that uses out-of-band management requires a direct connection to a console or AUX port, and a terminal emulation client.
What term is used to express the thickness or height of a switch?
Match the purpose to the related configuration item. (Not all options are used.)
What are two benefits of extending access layer connectivity to users through a wireless medium? (Choose two.)
Por favor, selecciona 2 respuestas correctas
Wireless connectivity at the access layer provides increased flexibility, reduced costs, and the ability to grow and adapt to changing business requirements. Utilizing wireless routers and access points can provide an increase in the number of central points of failure. Wireless routers and access points will not provide an increase in bandwidth availability.
Which design feature will limit the size of a failure domain in an enterprise network?
In order to best limit the of a failure domain, routers or multilayer switches can be deployed in pairs. The failure of a single device should not cause the network to go down. Installing redundant power supplies may protect a single device from a power failure, but if that device suffers from another type of problem, a redundant device would have been a better solution. Purchasing enterprise equipment that handles large flows of traffic will not provide extra reliability in times of an outage. If a collapsed core design is used, the core and distribution are collapsed into a single device, increasing the chance of a devastating outage.
A network administrator is planning redundant devices and cabling in a switched network to support high availability. Which benefit will implementing the Spanning Tree Protocol provide to this design?
With the implementation of redundant devices and links, redundant paths will exist in the network. This may cause a Layer 2 loop, and Spanning Tree Protocol (STP) is used to eliminate switching loops while maintaining reliability. STP is not required to combine multiple physical interfaces into a single EtherChannel interface. STP does not provide faster convergence or an expanded network that uses wired or wireless connectivity.
A network engineer is reviewing a network design that uses a fixed configuration enterprise router that supports both LAN and WAN connections. However, the engineer realizes that the router does not have enough interfaces to support growth and network expansion. Which type of device should be used as a replacement?
Modular routers provide multiple slots that allow a network designer to change or increase the interfaces that exist on the router. A Layer 3 switch may increase the number of ports available on a router, but will not provide WAN connectivity. The PoE capability of a device is not related to the number of ports it has. Using another fixed configuration router will not provide the flexibility to adapt to future growth that using a modular router will provide.
As the network administrator you have been asked to implement EtherChannel on the corporate network. What does this configuration consist of?
Immediately after a router completes its boot sequence, the network administrator wants to check the routers configuration. From privileged EXEC mode, which of the following commands can the administrator use for this purpose? (Choose two.)
Por favor, selecciona 2 respuestas correctas
The show startup-config command can be used to display the Cisco device configuration stored in NVRAM. The show running-config command can be used to display the currently active configuration that is stored in RAM. The show flash command displays the files (not file content) stored in the flash memory.
Which two features of enterprise class equipment assists an enterprise network in maintaining 99.999 percent up-time? (Choose two.)
Por favor, selecciona 2 respuestas correctas
Enterprise class equipment is designed with features such as redundant power supplies and failover capabilities. A failure domain is an area of a network that is impacted when a critical device fails. A collapsed core is a two-tier hierarchical design where the core and distribution layers are collapsed into a single layer. This reduces cost and complexity but does not provide redundancy and uptime.
What are three access layer switch features that are considered when designing a network? (Choose three.)
Por favor, selecciona 3 respuestas correctas
The port density of a switch (the number of ports available on a single switch), forwarding rate (how much data the switch can process per second), and Power over Ethernet (the ability of the switch to deliver power to a device over the existing Ethernet cabling) are access layer switch features to be considered when designing a network. Failover capability, speed of convergence, and broadcast traffic containment are distribution layer features.
What is a characteristic of in-band device management?
In-band device management is used to monitor and make configuration changes to a network device over a network connection. Configuration using in-band management requires at least one network interface on the device to be connected and to be operational, and it requires the use of Telnet, SSH, or HTTP to access the device.
What network design would contain the scope of disruptions on a network should a failure occur?
One way to contain the impact of a failure on the network is to implement redundancy. One way this is accomplished is by deploying redundant distribution layer switches and dividing the access layer switch connections between the redundant distribution layer switches. This creates what is called a switch block. Failures in a switch block are contained to that block and do not bring down the whole network.
What is the function of ASICs in a multilayer switch?
What are two functions of a router? (Choose two.)
Por favor, selecciona 2 respuestas correctas
Routers connect multiple networks in an organization to provide interconnections among them. They perform the task by using the network portion of the destination IP address to determine the best path to send packets to their destination.
What are two expected features of modern enterprise networks? (Choose two.)
Por favor, selecciona 2 respuestas correctas
All modern enterprise networks are expected to support critical applications, converged network traffic, diverse business needs, and provide centralized administrative control. Users expect enterprise networks to be up 99.999 percent of the time (not 90 percent.). Support for limited growth is not a usual network design criterion.
Comparte tus Resultados:
